Gyproc Thermaline Plus 40mm

Gyproc Thermaline Plus 40mm


Technical Information
Size 2400mm*1200mm
Thickness 40mm
Length2.4m
Width 1.2m
Category Gyproc Thermaline Plus Insulated Plasterboards
Product Name Size Unit Price Qty. Sub Total
 Gyproc Thermaline Plus 27mm Board thickness 27mm( 17.5mm insulation + 9.5mm plasterboard)
2400mm x 1200mm £44.28 £0.00
 Gyproc Thermaline Plus 35mm Board thickness 35mm( 25mm insulation + 10mm plasterboard)
2400mm x 1200mm £50.57 £0.00
 Gyproc Thermaline Plus 40mm Board thickness 40mm ( 30mm insulation + 10mm plasterboard)
2400mm x 1200mm £56.45 £0.00
 Gyproc Thermaline Plus 48mm Board thickness48mm ( 35mm insulation + 12mm plasterboard)
2400mm x 1200mm £64.40 £0.00
Dry wall Adhesive (25kg Bag)
25kg £10.44 £0.00
Delivered separately by courier.
Volume discounts apply automatically.



Product Summary

Gyrproc thermaline plus is a thermal laminate plasterboard consisting of extruded polystyrene stuck to to 9.5mm plasterboard ( Except 48mm which has 12.5mm plasterboard). It is has a medium level of performance of the boards in the thermaline range. Comparing the Thermaline Basic, Plus and Super board on a like for like basis we see that the thermal resistance of the 40mm Basic is 0.8m ²K/W, versus 1.05 for the Thermaline Plus 40mm and 1.49 ²K/W for the Thermaline Super 40mm.

  • Faced with ivory coloured Gyproc Wallboards
  • Backed with orange coloured extruded polystyrene
  • Available in tapered edge only
  • Complies with EN 13950
  • Thermal Conductivity: Wallboard 0.19W/mK
  • Thermal Conductivity: Plus extruded polystyrene 0.030W/mK

Technical Spec

27mm Board


Width

Length

Weight

Edge

Thermal resistance

mm

mm

kg/m²

T/S

m²K/W

1200

2400

6.5

T

0.63

35mm Board


Width

Length

Weight

Edge

Thermal resistance

mm

mm

kg/m²

T/S

m²K/W

1200

2400

7.2

T

0.88

40mm Board


Width

Length

Weight

Edge

Thermal resistance

mm

mm

kg/m²

T/S

m²K/W

1200

2400

7.7

T

1.07

48mm Board (faced with 12.5mm Gyproc Wallboard)


Width

Length

Weight

Edge

Thermal resistance

mm

mm

kg/m²

T/S

m²K/W

1200

2400

8.1

T

1.25


Gyproc Thermaline Plus 40mm



Product Application





Installation Instructions

It is important to observe appropriate health and safety legislation when working on site, i.e. personal protective clothing and equipment, etc. The following notes are intended as general guidance only. In practice, consideration must be given to design criteria requiring specific project solutions

Thermaline Basic Fixing

This product can be screwed or glued.
If you are wishing to glue it to the wall it should be glued with dry wall adhesive. If you are choosing this route you should use at least two mechanical fixings to hold it in place.

Gyproc Thermaline Super Cutting

This product may be cut using a plasterboard saw. Holes for switch or socket boxes should be cut out before the boards are fixed using a utility saw or sharp knife. When cutting boards, power and hand tools should be used with care and in accordance with the manufacturers’ recommendations. Power tools should only be used by people who have been instructed and trained to use them 
safely. Appropriate personal protective equipment should be used.

Gyproc Thermaline Super Fixing

Fix boards with decorative side out to receive joint treatment or a skim plaster finish. Lightly butt boards together. Never force boards into position. Install fixings not closer than 13mm from cut edges and 10mm from bound edges. Position cut edges to internal angles whenever possible, removing paper burrs with fine sandpaper. Stagger horizontal and vertical board joints between layers by a minimum of 600mm. Locate boards to the centre line of framing where this supports board edges or ends