Gyproc Thermaline Super Insulated Plasterboards

Name: Gyproc Thermaline Super Insulated Plasterboards
Brand: Gyproc
SKU: ZGRTLS50
Price: 101.92 GBP
Availability: InStock

£101.92

Sale Sold out

Price excludes VAT

Shipping calculated at checkout.

Product variants

Quantity

**Minimum order value of £300 applies, excluding taxes**

Gypsum plasterboard bonded to a phenolic foam insulant with an integral vapour control layer for an enhanced level of thermal insulation.

9.5mm Gyproc WallBoard bonded to CFC and HCFC-free meaning zero ODP (Ozone Depletion Potential), high performance phenolic foam insulant with an integral vapour control layer to reduce the risk of condensation. Designed to be used in both refurbishment and new build for walls, ceilings where a high level of thermal insulation is required to reduce heat loss from buildings as part of British Gypsum's BBA approved systems.

Have you seen the rest of the Gyproc Thermaline range?

Product Summary

Gyrproc Thermaline super is a thermal laminate plasterboard consisting of phenolic foam (the same stuff as is used in Kingspan K118 we are told) stuck to to 9.5mm plasterboard . It is has a highest level of performance of the boards in the Gyproc Thermaline range.

Comparing the Gyproc Thermaline Basic, Plus and Super board on a like for like basis we see that the thermal resistance of the 40mm Basic is 0.8m ²K/W, versus 1.05 for the Thermaline Plus 40mm and 1.49 ²K/W for the Thermaline Super 40mm.

Other Info

It has good fire performance, with Class 0 rating to both faces. Also has low toxicity and smoke obscuration of less than 5%. Includes a vapour control layer as standard to reduce risk of condensation.

Faced with ivory coloured Gyproc WallBoard
Backed with brown coloured phenolic foam
Available in tapered edge only
Complies with EN 13950
Thermal Conductivity: WallBoard 0.19W/mK
Thermal Conductivity: Super phenolic foam 0.020W/mK to 0.022W/mK (dependent on thickness of foam)

Technical Spec

40mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.4	T	1.49

50mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.5	T	1.97

60mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.6	T	2.56

70mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.7	T	3.06

80mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.8	T	3.56

90mm Board

Width	Length	Weight	Edge	Thermal resistance
mm	mm	kg/m²	T/S	m²K/W
1200	2400	6.9	T	4.06

Gyproc Thermaline Super 50mm

Product Application

Installation Instructions

It is important to observe appropriate health and safety legislation when working on site, i.e. personal protective clothing and equipment, etc. The following notes are intended as general guidance only. In practice, consideration must be given to design criteria requiring specific project solutions

Thermaline Basic Fixing

This product can be screwed or glued.

If you are wishing to glue it to the wall it should be glued with dry wall adhesive. If you are choosing this route you should use at least two mechanical fixings to hold it in place.

Gyproc Thermaline Super Cutting

This product may be cut using a plasterboard saw. Holes for switch or socket boxes should be cut out before the boards are fixed using a utility saw or sharp knife. When cutting boards, power and hand tools should be used with care and in accordance with the manufacturers’ recommendations. Power tools should only be used by people who have been instructed and trained to use them

safely. Appropriate personal protective equipment should be used.

Gyproc Thermaline Super Fixing

Fix boards with decorative side out to receive joint treatment or a skim plaster finish. Lightly butt boards together. Never force boards into position. Install fixings not closer than 13mm from cut edges and 10mm from bound edges. Position cut edges to internal angles whenever possible, removing paper burrs with fine sandpaper. Stagger horizontal and vertical board joints between layers by a minimum of 600mm. Locate boards to the centre line of framing where this supports board edges or ends

View full details

We are here to help

Let our expert team find the right product for you